纤维增强复合材料螺接接头挤压强度的估算方法

羊姈

纤维增强复合材料螺接接头挤压强度的估算方法

羊姈

西北工业大学

计量
- 文章访问数: 2095
- HTML全文浏览量: 181
- PDF下载量: 583
- 被引次数: 0
出版历程
- 收稿日期: 1983-05-03
- 刊出日期: 1986-01-15

An Estimation Method of Bearing Strength of Bolted Joints in Fibre Reinforced Composite

Yang Ling

Department of Aircraft Engineering Northivestern Polytechnical University, Xi'an

摘要

摘要: 一些研究者采用比较简单有效的工程方法来估算纤维增强复合材料螺接接头的强度,但是这些方法均未考虑由于螺栓拧紧后对螺栓强度的影响。本文在对试验结果观察分析的基础上提出一种单孔螺接接头的临界挤压强度的估算方法,考虑了螺栓拧紧的效应。计算结果与碳/环氧迭层试验结果有较好的一致性。

Abstract: Some researchers have estimated the strength of bolted joints in fibre reinforced composite, using simple and efficient engineering procedures. However, for these procedures the effect of clamping due to the strength of bolted joints is not considered. In this paper, a method is presented for predicating critical bearing strength of single-hole bolted joints in composite on the basis of observing and analysing the results of experiments. The clamping effect of bolts is considered. The calculated results correspond to the test data on Glaphic/Epoxy laminates.

HTML全文

参考文献(16)

[1]	羊姈,复合材料螺栓连接设计,西工大科研资料SHJ 8056期,(1980).
[2]	Waszezak,J.P.and T.A.Cruse.Failure mode and strength prediction of anisotropic bolt bearing specimens,J of Composite Materials,5(1971),421.
[3]	Jong,Theo.De., Stresses around pin-loaded holes in elastically orthotropic or isotropic plates,J.Composite Materials.2(1977),313.
[4]	Eisenmann,J.R.,Bolted joint static strength model for composite materials,NASA-TM-X-3377(1976).
[5]	Hart-Smith,L.J.,Bolted joints in graphite epoxy composites.Douglas Aircraft Company,NASA Contract Report,No NASA CR-144899(1976).
[6]	Collings,T.A.,The strength of bolted joints in multidirectional CFRP laminates,Composites.8(1977).
[7]	Quinn,W.J and F.L.Matthews,The effect of stacking Sequence on the pin-bearing strength in glass fibre reinforced plastic,J Cmposite Materials.2(1977),139.
[8]	Kim,R.Y and J.M.Whitney,Effect of temperature and moisture on pin bearing strength of composite laminates,J Composite Materials.10(1976),149.
[9]	Wilson.D.W and R B.Pipes.Analysis of the shearout failure mode in composite bolted joints,Composite Structure.p 34.
[10]	Tang,S.,Failare of composite joint under combined tension and bolt loads.J Composite Materials.15(1981),329.
[11]	Soui,S.R.,Failure analysis of composite laminates with a fastener hole.Joining of Composite Material.p.145.
[12]	Soni.S.R.,Stress and strength analysis of bolted joints in composite laminates,Composite structure,p.50.
[13]	吴金泉,碳纤维/环氧树脂复合材料迭层板螺栓接头强度试验及应力集中统数的研究,航空工业部625所.
[14]	陈绍傑等,复合材料连接试验报告,航空工业部601所.
[15]	杨炳章等,碳纤维/环氧复合材料迭层板挤压强度的实验研究,西工大科技资料SHJ 8489期,(1982).
[16]	羊姈,碳纤维复合材料迭层平板孔边应力分析,西工大科技资料SHJ 8217期,(1982).